Sale!

SpeedyBee F405 V3 BLS 50A 30×30 FC&ESC Stack

Original price was: $69.99.Current price is: $52.13.

+ Free Shipping
Packaged with more useful features
● Built-in barometer for accurate height calculation
● SD Card slot can support up to 4GB Blackbox data*
● Dedicated DJI Air Unit connector for a quick digital build
● 9V 2A + 5V 2A individual BECs
● 4 x UARTs for your receiver + VTX + camera + GPS.
● Power your GPS with a USB cable – no battery needed.
No extra heat, no worries.
● 22mm cutouts for FPV camera in your tight build

SpeedyBee F405 V3 BLS 50A 30×30 FC&ESC Stack

The SpeedyBee F405 V3 BLS 50A 30×30 FC&ESC Stack features Bluetooth Pairing & Configuration, Onboard 4-level Battery Indicators, 1500uF Filtering Capacitator, Built-in Barometer, to name a few. It also offers 4x UARTS, 5V 2A &9V 2A individual BECs, Wireless Motor-direction Changing, 4x LED Strips Soldering Pads, 4GB Max Blackbox SD Card Slot, and 8 Motors Support.

Features

F405 V3 FC

  • Dedicated DJI Air Unit connector for a quick digital build 
  • Power your GPS with a USB cable – no battery needed.
  • 4 x UARTs for your receiver + VTX + camera + GPS.
  • SD Card slot can support up to 4GB Blackbox data*
  • 22mm cutouts for FPV camera in your tight build
  • 9V 2A + 5V 2A individual BECs
  • 4-level LED battery indicator
  • m1-m8 ESC signal
  • Built-in barometer
  • Bluetooth pairing

50A 3-6s BLHeli_S 4-in-1 ESC

  • Large motor pads for easy soldering
  • Smooth flight experience
  • 1500uF ESR Capacitator
  • TVS diode
  • 30×30 mounting holes
  • Robust BB21 MCU
  • BLHeli_S JH50

 

Specifications

Product Name SpeedyBee F405 V3 FC
BOOT Button Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to control the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
Blackbox MicroSD Card Slot  *Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High Capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also, the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose ‘Overwrite format’ and then format your card. Also, check out here for the recommended SD cards or buy the tested cards from our store.
5V Output  9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on the front side, and 4x LED 5V pads. The total current load is 2A.
Traditional Betaflight LED Pad Supported. 5V, G, and LED pads on the bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
9V Output 2 groups of 9V output, one +9V pad on the front side and the other included in a connector on the bottom side. The total current load is 2A.
4.5V Output  Supported. Designed for the receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
Power Input 3S – 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
Current Sensor Input Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
DJI Air Unit Connection Way 6-pin connector or direct soldering.
I2C Supported. SDA & SCL pads on the front side. Used for magnetometer, sonar, etc.
Supported Flight Controller Firmware BetaFlight(Default), EMUFlight, INAV
UART 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6)
BLE Bluetooth Supported. Used for Flight Controller configuration
SmartPort Use any TX pad of UART for the SmartPort feature.
ESC Signal M1 – M4 on the bottom side and M5-M8 on the front side.
BetaFlight Camera Control Pad Yes(CC pad on the front side)
RSSI Input Supported. Named as RS on the front side.
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Buzzer BZ+ and BZ- pad used for 5V Buzzer
Firmware Target Name SPEEDYBEEF405V3
Dimension 41.6(L) x 39.4(W) x 7.8(H)mm
ESC Telemetry UART R4(UART4)
OSD Chip AT7456E chip
USB Port Type Type-C
IMU(Gyro) BMI270
Barometer Built-in
MCU STM32F405
Weight 9.6g

 

Product Name SpeedyBee 50A 3-6s BLHeli_S 4-in-1 ESC
Firmware BLHeli_S JH50
Wireless Configuration Full Configuration Supported in the SpeedyBee app
PC Configurator Download Link https://esc-configurator.com/
Continuous Current 50A * 4
Burst Current 55A(5seconds)
TVS Protective diode Yes
External Capacitor 1000uF Low ESR Capacitor(In the package)
ESC Protocol DSHOT300/600
Power Input 3-6S LiPo
Power Output VBAT
Current Sensor Support (Scale=386 Offset=0)
ESC Telemetry Not supported
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Dimension 45.6(L) * 44(W) * 6.1mm(H)
Weight 13.8g

Links

Includes

F405 V3 FC

  • 1x SH 1.0mm 30mm-length 8pin cable(for FC-ESC connection)
  • 1x SpeedyBee F405 V3 Flight Controller – 30×30
  • 5x M3x8mm Silicone Grommets(for FC)
  • 1x DJI 6pin cable(80mm)

50A 3-6s BLHeli_S 4-in-1 ESC

  • 1x SH 1.0mm 30mm-length 8pin Cable(for FC-ESC connection)
  • 1x SpeedyBee 50A 3-6S BLHeli_S 4-in-1 ESC – 30×30
  • 5x M3x8.1mm Silicone Grommets(for ESC)
  • 1x 35V 1500uF Low ESR Capacitor
  • 1x XT60 Power Cable(70mm)
  • 5x M3 Silicone O Ring

Reviews

There are no reviews yet.

Be the first to review “SpeedyBee F405 V3 BLS 50A 30×30 FC&ESC Stack”

Your email address will not be published. Required fields are marked *

Shopping Cart
Select your currency
USD United States (US) dollar